Hook up double switch

It is very important to connect the ground wire to the switch as well. The Green screw on the 2-way switch is for the ground so all ground wires should be connected as seen below.

All ground wires bare copper are all now connected incoming ground, load ground and switch ground. This makes for a safe protected circuit by having all grounds intact. So what have we accomplished. By wiring a 2-way switch, The circuit below shows the basic concept of electricity flow to the load. Let's assume the load you are controlling is a light. The electricity flows from the hot wire black through the 2-way switch shown in off position and then to the light and returns through the neutral wire white.

This is a completed circuit. Now by understanding the diagram above, go up to the top diagram and by using the concept shown here, just use your mouse pointer on that diagram and follow the flow from black wire hot wire to the load and return through the white wire neutral. This should give you a good basic understanding how the 2-way switch circuit works and will help you in adding or changing a 2-way switch.

So now that you have a basic concept of wiring a 2-way switch, let's look at the following 2-way switch diagrams to see which type of circuit scenario you have. After you have pulled your switch out from the wall, the wires in the box and connecting to the switch should look like one of the following.


  • Connect the LEDs to an on/off switch (video) | Khan Academy.
  • list of interests for dating sites.
  • k-ar dating range?

Video transcript All right. So we're almost there.

electrical - How can I replace a single switch with two switches? - Home Improvement Stack Exchange

Now, what we're going to do is we're going to wire our LEDs, so our eyes, so that they light up. And we're going to use the other sliding single-pull, double-throw switch to do that.

Leviton Presents: How to Install a Decora Combination Device with Two Single Pole Switches

So we're going to take our needle nose, and again, we'll put a little loop in the white wire that we had remaining from our previous that we made earlier in the videos. And we're going to loop that around one of our remaining contacts on our single-pull, double-throw switch. And again, it's a little tricky. You want to make sure that you get a pretty tight loop. And then, you'll push it around that contact. And once you've got it on there, you can take your needle-nose pliers and just make sure that it's crimped tightly against the terminal that's exposed from the switch there.

And again, you want to make sure that it's not touching any of the other terminals. So if it is, the switch will always stay on, and it won't work properly. I'm just twisting it very tightly here to make sure that it's very firmly connected.

Spout Bot without Solder

So now what we need to do is we need to connect another wire to our resistor leads from our LEDs that we created earlier in the previous videos. And I'm going to go ahead and bend this other terminal on the switch out of the way that we don't need. And again, that's the one that's on the far side of the sliding switch there.

So now we have our wire from our battery, which is our negative wire. And we're going to connect back to our resistors.

Pole Switches

And we're just stripping off a little piece of-- we're using the white wire again. We're going to strip off a little piece of the white wire there. Generally speaking, if you take just a little bit more insulation off, it's a little easier because you have a little bit more wire to loop around. But it also means that you have more that you have to cover up once you're done.

Connect the LEDs to an on/off switch

It's kind of tricky, but a quarter of an inch works for me. In any case, you can just use the wire strippers there and pull the wire. If you wiggle it around a little bit, it'll come out and strip off the wire there. And again, we're going to take our needle-nose pliers, and we're going to loop these around and create the loop to go over the terminal there. Once we have the loop done, we'll use our needle-nose pliers to crimp it in place. So once it's crimped in place, we can hot glue it.


  • Wiring help for Leviton double switch | Leviton Online Knowledgebase.
  • free dating sites in milwaukee!
  • 37 dating 25 year old!
  • albion speed dating?
  • dating after rape?
  • free online dating fish?